Shure AXT630 Axient Antenna Distribution System

Shure AXT630 Antenna Distribution Systems send the RF signal from a single pair of antennas to multiple receivers. Ultra-linear amplification and adjustable attenuation optimize performance in difficult RF environments. Selectable input filters match the available frequency bands of transmitters, providing extra protection from strong out-of-band signals. BNC antenna output pairs distribute band-filtered signal to up to 4 receivers. A pair of wideband cascade ports supplies a wideband RF signal to Spectrum Managers or additional antenna distribution amplifiers. Networking enables Wireless Workbenchr 6 system control of filtering ranges and attenuation. To maximize use of available RF spectrum, two models of the Antenna Distribution System are available. The AXT630 covers a frequency range of 470-698 MHz and the AXT631 covers a frequency range of 606-814 MHz.

Features:

• Selectable input filtering provides system-wide protection against strong out-of-band signals
• Wideband filtering option covers multiple bands
• Up to 15 dB of selectable RF attenuation for signal-to-noise optimization
• Front panel interface and Wireless Workbench 6 software control provide easy setup and control of filtering, antenna power, and attenuation
• BNC outputs: 4 antenna output pairs
• Wideband RF cascade port with selectable 3 dB make-up gain for connecting wideband devices
• Ethernet Networking: 2 PoE enabled Ethernet ports
• IEC power ports enable daisy-chaining of AC power

Specifications:

• RF Input
• Connector Type: BNC
• Configuration: Unbalanced, active
• Band Filters AXT630:
  Wideband: 470-698 MHz
  Band G1: 470-530 MHz
  Band H4: 518-578 MHz
  Band J5: 578-638 MHz
  Band L3: 638-698 MHz
• Impedance: 50Ω
• Bias Voltage: 12 V DC, 150 mA (300 mA maximum)
• RF Frequency Range: AXT 630: 470-698 MHz

  Distribution Output

• Connector Type: BNC (4 pairs)
• Configuration: Unbalanced, active
• Impedance: 50Ω
• Gain Adjustment Range Cascade Enabled: -15 dB to 0 dB (In 1 dB steps)
• Cascade Disabled: -12 dB to +3 dB (In 1 dB steps)
• Output Intercept Point: >25 dBm, typical

  Cascade Output

• Connector Type: BNC (1 pair)
• Configuration: Unbalanced, wideband
• Impedance: 50Ω
• Insertion Loss: <5 dB

  Networking

• Power Over Ethernet (PoE): 50 V DC, Class 1
• Network Interface: Dual Port Ethernet 10/100 Mbps
• Network Addressing Capability: DHCP or Manual IP address

  General

• Dimensions (HxWxD): 1.7 x 19 x 14.4″ (44 x 483 x 366mm)
• Weight: 10.1Lbs (4.6kg)
• Housing: Steel; Extruded aluminum
• Operating Temperature Range: -18°C (0°F) to 63°C (145°F)
• Storage Temperature Range: -29°C (-20°F) to 74°C (165°F)
• Power Requirements: 100 to 240 V AC, 50-60 Hz
• Current Drain: 1.0 A RMS (referenced at 120 V AC)

Item Includes:

• 2-foot Coaxial Antenna Cable (RG-58) (12) UA802
• IEC AC Power Cable (1) 95A9128
• IEC AC Extension Cable (1) 95A9129
• Shielded 3-foot Ethernet Cable (1) C803
• Shielded 8-inch Ethernet Jumper Cable (1) C8006
• Hardware Kit (1) 90XN1371
• 22-inch Coaxial Cable (1) 95B9023
• 33-inch Coaxial Cable* (1) 95C9023